Water Absorption
D-570
0.06%
General: Poly-Tuf Flat Panels are intended for interior use only, not for exterior use. Make sure panels are clean and dry. Clean with general household cleaners, wiping in one direction only.
Adhesives: Latex or water-based adhesives are recommended. Follow adhesive manufacturer’s directions. Spread adhesive with notched trowel over the entire back side of panels, leaving no areas uncovered, to assure a proper bond.
Pre-Drilling: If using plastic rivets, pre-drill 3/8” diameter holes in panels to allow for thermal movement, then drill 1/4” diameter holes into wall to accept rivets. Follow rivet manufacturer’s directions.
1190 PSI
78.249
Non-Flammable Adhesive
Franklin Titebond Fast Grab FRP
Properties: Water Absorption
ASTM Test Method: D-570
Typical Adhesive: 0.06%
Properties: Flame Spread
ASTM Test Method: D-570
Typical Adhesive: 0.06%
Properties: Smoke Developed
ASTM Test Method: E-84
Typical Adhesive: CLASS C
Properties: Gardener Impact
ASTM Test Method: D-3029
Typical Adhesive: 5.0 in. lb.
Properties: Shore Hardness
ASTM Test Method: D-2440
Typical Adhesive: 51
Properties: Tensile Strength
ASTM Test Method: D-638
Typical Adhesive: 1190 PSI
Properties: Heat Deflection
ASTM Test Method: D-648
Typical Adhesive: 78.249
Properties: Flexural Modulus
ASTM Test Method: D-790
Typical Adhesive: 78.240
Non-Flammable Adhesive: Henry #444 FRP Panel Adhesive
Rating: 4.0
Non-Flammable Adhesive: Liquid Nails FRP #310 Latex FRP Adhesive
Rating: 3.5
Properties: DAP Weldwood Multi-Purpose Flooring Adhesive
Rating: 3.5
Properties: Franklin Titebond Fast Grab FRP
Rating: 2.0
Properties: OSI Sealants, Inc. Pro Senes FRP-555
Rating: 2.0
Properties: TACC/Miracle FRP Adhesive
Rating: 1.5
Sizes: 48″x96″, 48″x120″
Thickness: .090″
Colors: Bright White and Almond
Packaging: 100 pieces per pallet
Material: Minimum 70% recycled polyolefin content
Poly-Tuf flat panels must be installed over a solid surface such as gypsum wallboard. Do not install directly to studs or framing material. Surface must be sound, dry, and free of dust, dirt, oil, grease, or loose paint. Level surface by removing high spots and filling low areas, holes, or gaps. Make sure fillers or leveling compounds are fully cured and dry prior to panel installation
To all for thermal expansion, cut flat panels so as to allow at least 1/4″ (6mm) gap at top and bottom, and to allow at least 1/8″ (3mm) gap at sides of each panel. Failure to do so may result in buckling of panels.
Allow at least 1/8″ (3mm) gave when cutting panels to fit around pipes, electrical outlets, etc. When using moldings (recommended), cut panels to allow 1/8″ (3mm) gap between panel edges and bottom of molding channels.
Cut panels with a fine- toothed hand or power saw. Use hole saw or utility knife to trim or to cut off shapes as required
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
110 Railroad Drive
Ivyland, Pennsylvania 18974
Toll Free: 800-474-2732
Phone: 215-355-0250
Fax: 215-355-4066
Copyright © 2025 hfmfgcorp.com
Website Design By IQnection – A Digital Marketing Company
Copyright © 2025 hfmfgcorp.com
Website Design By IQnection – A Digital Marketing Company